[scribus] Page numbers blanking out

[Mark Cornwell]

Hello,



I'm new to Scribus. I've been designing a layout for a photo book with text.



I've put in lots of pages and images/text etc. Then I went to create a TOC.



I also spotted the Ctrl+Alt+Shift+P to add a page number to a page and to
add a text box with that in it on the master.

I also found out how to set up page numbering to start after the TOC via
Document Setup>Sections.



So far so good.



My document now has three pages with no page numbering (intro/TOC) and then
starts with page number 1 on page layout 4.



That's all working.



What I can't work out is that when I get to page 10 the page numbers just go
blank again.



My sections have:

Name 0, Shown tick, From 1, To 3, Style None, Start 1.

Name 1, Shown tick, From 4, To 57, Style 1,2,3., Start 1.



I've not "stopped" the section at page 10.



I have tried applying the master again to all pages. That didn't make any
difference. All I see on pages 10 and beyond in Scribus is a rectangle with
a small box with a cross in it to the bottom right. If I create a PDF via
Export then it leaves the page numbers empty on pages 10 and beyond.



Just in case it is relevant - pages 34 and onwards are currently blank.



Any bright ideas, please?



Thanks,

Mark

-------------- next part --------------
An HTML attachment was scrubbed...
URL: <http://lists.scribus.net/pipermail/scribus/attachments/20180205/ed36c8c1/attachment.html>
___
Scribus Mailing List: ***@lists.scribus.net
Edit your options or unsubscribe:
http://lists.scribus.net/mailman/listinfo/scribus
See also:
http://wiki.scribus.net
http://forums.scribus.net

[Gregory Pittman]

Post by Mark Cornwell
Hello,
I'm new to Scribus. I've been designing a layout for a photo book with text.
I've put in lots of pages and images/text etc. Then I went to create a TOC.
I also spotted the Ctrl+Alt+Shift+P to add a page number to a page and to
add a text box with that in it on the master.
I also found out how to set up page numbering to start after the TOC via
Document Setup>Sections.
So far so good.
My document now has three pages with no page numbering (intro/TOC) and then
starts with page number 1 on page layout 4.
That's all working.
What I can't work out is that when I get to page 10 the page numbers just go
blank again.
Name 0, Shown tick, From 1, To 3, Style None, Start 1.
Name 1, Shown tick, From 4, To 57, Style 1,2,3., Start 1.
I've not "stopped" the section at page 10.
I have tried applying the master again to all pages. That didn't make any
difference. All I see on pages 10 and beyond in Scribus is a rectangle with
a small box with a cross in it to the bottom right. If I create a PDF via
Export then it leaves the page numbers empty on pages 10 and beyond.
Just in case it is relevant - pages 34 and onwards are currently blank.
Any bright ideas, please?

Have you checked to make sure you have applied the master page to 10 and
beyond?

Greg


___
Scribus Mailing List: ***@lists.scribus.net
Edit your options or unsubscribe:
http://lists.scribus.net/mailman/listinfo/scribus
See also:
http://wiki.scribus.net
http://forums.scribus.net

[Mark Cornwell]

This almost certainly means that your text box is too small for a

double-digit page number.

Christoph, spot on! It looked plenty big enough but for some reason wasn't.
When I increased the width a touch it all worked fine. Thanks for your help.

Mark


___
Scribus Mailing List: ***@lists.scribus.net
Edit your options or unsubscribe:
http://lists.scribus.net/mailman/listinfo/scribus
See also:
http://wiki.scribus.net
http://forums.scribus.net